As the world's leading steel supplier, we can provide a wide range of steel types, including carbon steel, weathering steel, boiler steel, structural steel, etc., and we can meet customers' requirements in any size, as well as the production of steel and complete plant plans. If you are interested in these aspects, please contact us.
steel properties A2 Steel is equivalent of DIN 2363 and it provides extreme hardness after heat treatment with great dimensional stability. It is heat treatable and offers hardness in AISI H10 Hot Work Steel AISI H10 Die Steel AISI H10 Hot Work Steel AISI H10 is equivalent steel of DIN 2365 with good high-temperature toughness and high tempering resistance, less Susceptibility to high hot cracking, good thermal conductivity, Can be water-cooled to a limited extent.
What is S7 Tool Steel? In tool steel standard ASTM A681, shock-resisting tool steels are designated as group S steels according to the AISI classification system. S1, S2, S5, S6, and S7 are the types of shock-resisting tool steels. AISI S7 tool steel is a shock-resistant air hardening steel. AISI S7 steel AISI/SAE SteelsH10:Alloyed hot work tool steel SITHERM 2885:H10A:Alloyed hot work tool steel SITHERM 2343:H11:Alloyed hot work tool steel SITHERM 2344:H13:Alloyed hot work tool steel SITHERM 2345:Approx.H11:Alloyed hot work tool steel SIHARD K560:A8 mod. Alloyed hot work tool steel SITHERM S363:A9:Alloyed hot work tool steel ATA SHEET - CarpenterLSS 2367 Hot Work Tool Steel DIN 1.2367 Typical Composition C Mn Si Cr Mo V 0.38 0.45 0.40 5.00 3.00 0.55 LSS 2367 is a chromium-molybdenum hot work steel that is similar to AISI H11 hot work steel, but which contains a higher molybdenum content. The higher molybdenum
Minimum order 6 or 10 tonnes depending on steel grade and condition. Hardened and tempered acc. to EN:ISO 898-1 Alloyed steel for case hardening SS-EN 10277-4 16MnCrS5 20MnCrS5 16NiCrS4 SS SS 2511 Dimensions mm 16 - 70 mm 1) 6 - 70 mm ) 6 - 70 mm 1) 6 - 70 mm 1) Tolerance ISO (round) h10 h10 h10 h10 Atlas M1020 Carbon Steel Bright Bar M1020Carbon Steel Bright Bar M1020 Colour code:Yellow Introduction Atlas M1020 carbon steel bar is a merchant grade plain carbon steel bar containing nominally 0.20% carbon. Atlas M1020 has wider chemical composition limits than grade 1020. Grade M1020 is supplied based on it meeting specified chemical composition requirements only. Carbon Steel Round Bar, Carbon Steel Hex Bar, CS Flat Bar Carbon Steel Bright Bar and Carbon Steel Square Bar, CS Hex Bar suppliers in India Buy Carbon Steel Flat Bar, Carbon Steel Forged Bar, Carbon Steel Rounds Stock at factory price in Mumbai, India. Medium-carbon steel Round BarApproximately 0.30.8% carbon content. Balances ductility and strength and has good wear resistance; used for large
40HRC pre-hardened steel. Press forming dies for small production, jigs and tools. High speed steel with high abrasion resistance and toughness for general use. High speed steel to prevent from abrasion, seizure and deformation under high pressure Cold forging dies, cold heading dies, slitter. Matrix high speed steel, extremely highest toughness in H10 ( AISI, ASTM, UNS) - Worldwide equivalent gradesH10 (USA, AISI, ASTM, UNS ) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Buy, sell, suppliers search product H10 on-line H10 Steel Chemical composition, Metal Properties H10 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. TEL:+86-80247006 E-mail:[email protected]
H13 Tool Steel is chromium hot work tool steels which are widely used in hot and cold work tooling applications. H13 tool steel is classified as group H steels by the AISI classification system. This series of steels start from H1 to H19. AISI H-13 tool steel is characterized by:Good resistance to abrasion at both High Speed Steel H13 Steel H13 H13 Technical DataH13 Tool Steel. H13 Tool Steel is a versatile chromium-molybdenum hot work steel that is widely used in hot work and cold work tooling applications. The hot hardness (hot strength) of H13 resists thermal fatigue cracking which occurs as a result of cyclic heating Hot Work Mold Steel H10 Hot Rolled Steel Plate - Buy 1 Hot Work Mold Steel H10 Hot Rolled Steel Plate , Find Complete Details about Hot Work Mold Steel H10 Hot Rolled Steel Plate,1.2365 Steel Plate,Skd7 Steel Plate,4cr3mo3siv Steel Plate from Supplier or Manufacturer-Dongguan Songshun Mould Steel Co., Ltd.
This grade is an oil hardening tool steel type supplied in the annealed condition. STEEL PROPERTIES. OHNS O1 cold work steel is an equivalent of DIN 2510. The grade AISI O1 tool steel is an oil-hardening, non-shrinking tool steel and has a good cutting edge retention, high hardenability and dimensional stability during heat treatment. APPLICATION Tool steel and Hard alloy - Steel grades, Properties and Data Table for:Steel Grades > Tool Steel And Hard Alloy > USA ASTM H10, - Steel GradesStainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. H10 Round Bar H10 Flat Bar H10 Hollow Bar H10 Tube / Pipe H10 Sheet / Plate H10 Strip / Coil H10 Wire H10 Forging H10 Tube / Pipe H10 Fastener / Bolt / Nut / Screw Welding Parts M/B:+86-80247006 E-mail:[email protected] Website:https://tool-die
The Rapid Response pre-engineered product line offers the most comprehensive pre-engineered steel structures in the industry. Rapid Response V-Series is the ideal solution for standardized structures larger than H10 and are available in round or 12-sided steel. Complete catalog poles from Class 5 to V-20 are available in PLS-POLE for use in 1.2365, 32CrMoV12-28, AISI H10 - tool steelRound bars, forgings, flat bars, cutted elements and flats in hot work tool steel 1.2365, 32CrMoV12-28, X32CrMoV3-3, AISI H10 acc. to ISO 4957.